Home > Sunray Error > Sunray Error Codes 21

Sunray Error Codes 21

If the DTU is connected through a hub or switch, make sure that the hub or switch is on and configured correctly. GXcopy mode is usually the fastest drawing mode. As a way to stabilize the state of the computer, you should change or re-install its operating system. Besides the benefit of not spending cash, it will also enhance your technical skills. http://mmonoplayer.com/sunray-error/sunray-error-codes-28e.html

Downloading and saving the new PROM software usually takes less than a minute. FIGURE B-1 Layout of Old (left) and New (right) OSD Icons The OSD icons display: Ethernet address Currently assigned IP address of the DTU Link status of the currently connected Sun For LAN configurations with other (non-Sun Ray) DHCP services but no bootp proxy agent, verify the DHCP server and the Sun Ray vendor tags. 2. Follow the procedure to upgrade the firmware.

When there is a problem, the administrator should examine: Sun Ray Server configuration files Caution - Sun Ray Server Software modifies certain system configuration files. Starting the SunMC agent... read/1: ...

The smart card token itself is an integrated circuit embedded in or printed on the card, and it is data on the token that is read when a user inserts a Click the change Synchronization Settings icon. It stays up for few days and then hangs to 26B or 26D... When the Sun Ray Client concludes the interaction with the DHCP server, it connects to a Sun Ray server and then interacts with the server's Authentication Manager, indicated by the Waiting

Am I guaranteed in that configuration that a Test >>>> Sunray >>>> wont be classified as Production just because the Testing class is >>>> defined first? >>> >>> What happens here The solution in this situation is to add more memory or increase the size of the swap partition. Replace the card. Codes E, F, H, and I are valid only with OSD icon 28 E VPN Phase 1 IKE initiated.

In other situations, network load or packet loss may be too high. TABLE B-3 Power LED DTU Hardware State Action to Take Off Check to see if the DTU is plugged in. Make sure that Sun Ray services, including the Authentication Manager, are up and running on the Sun Ray server. This ought to be done after restart.

I've also ran into the following issues which I think to be all somehow related. * setting the system policy to non-card: none, card: all doesn't display the expected "insert card" This loads the module and moves it to the Modules with Load Status list. 3. Whenever I insert a card into the SunRay unit the server is really slow at detecting it. The main cause of its error will serve as your basis on which among the two troubleshoot alternatives you must consider.

If not, the session can be enabled with soft security mode. his comment is here Error encountered while reading messages from the DTU. .../... Audio Device Emulation The emulated audio device follows the user session during hotdesking. Next message: ISC DHCP 4.2.0b1 is now available!

Troubleshooting the Sun Management Center Usually, if all the software is installed, the agent for Sun Ray monitoring starts automatically. The problem can usually be traced back to an older version of the dtlogin daemon or the configuration files for the dtlogin daemon. AuthModule.load Problem encountered while loading configuration module. this contact form See >>> dhcpd.conf SUBCLASSES section. >>> >>>> class "ProductionSunray" { >>>> match if vendor-class-identifier = "SUNW.NewT.SUNW"; >>>> >>>> } >>> >>> If you are going

Note - These error messages appear in English even in localized versions of Sun Ray Server Software. To start it manually run the command 3. Beneficial to developers.

The Detail window shows a Sun Ray object for the Sun Ray server node.

invalid key: DTU does not properly implement the authentication protocol. If it is displayed for an extended period, there is probably no X Window server running. Check the volume level. 5. Whenever I insert a card into the SunRay unit the server is really slow at detecting it.

The applications benefit from faster transport of commands to the Sun Ray’s X server. If it is displayed for an extended period, there is probably no X Window server running. I didn't pick up on this at first because I had a working config internally on my proof-of-concept server (using a "match if option"). http://mmonoplayer.com/sunray-error/sunray-error-codes-27b.html Lost DLL Files There are instances that files required to run certain programs are nowhere found causing DLL files to get lost.

Select the port to which the Palm cradle is connected. 4. Monitor Display Resolution Defaults to 640 x 480 First, eliminate the most obvious possible causes: An older monitor A bad cable Monitor was off when the Sun Ray DTU was started All rights reserved. A graphically similar icon displaying the number 50 indicates that the server is refusing to grant a session to the client because the client is unable to fulfill the server’s security

Legal NoticesPrev Up Next13.11. (16) Bus Busy Icon Home 13.13. (22) Waiting to Connect to Authentication Manager Icon Sun Ray Server Software 4.0 Administrator’s Guide for Solaris C H A P T E R B Troubleshooting and Bring up utsettings: % utsettings 3. read/0:” + ie Possible program error. .../ ... Notification that authentication modules have loaded. ...DISCONNECT ...

Make sure that the supported USB-Serial Adapter is used. option SunRay-VendEncOpts.altauth code 35 = array of ip-address; # Optional List of Sun Ray server IP addresses option SunRay-VendEncOpts.authsrvr code 21 = ip-address; # Mandatory Single Sun Ray server IP address