Home > Sunray Error > Sunray Error Code 21

Sunray Error Code 21

AdminJobQ--Used in the implementation to wrap a library that would not otherwise be thread-safe. Cheers, Anton -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of "Øystein E. This loads the module and moves it to the Modules with Load Status list. 3. Start the application again. http://mmonoplayer.com/sunray-error/sunray-error-code-28e.html

Check the network drop cable. Verify that your DHCP server is configured properly for network parameters. When DHCP has finished, the Sun Ray DTU tries to connect to a Sun Ray server and the authentication manager that is running on that server. Consider using a powered hub. 11 Server is authenticated by the Sun Ray and the graphic/keyboard network connection is encrypted 12 The Sun Ray cannot authenticate the server but the graphic/keyboard

Cannot find module Program or installation error. Amber Hardware fault. This needs a >>> leading 1 which represents ethernet. >>> >>> subclass "TestingSunray" 1:xx:xx:xx:xx:xx:xx; >>> >>> The sub-class uses a fast hashing algorithm to determine membership, >>> so it's efficient even

TABLE B-4 Firmware Download Error Codes and Messages Error Code Error Message E FW Load: No server F FW Load: Name too long G FW Load: Bad read H FW Load: It is easy to identify possible solutions through this. I've also ran into the following issues which I think to be all somehow related. * setting the system policy to non-card: none, card: all doesn't display the expected "insert card" Pre-Installation Foreword It is recommended that all DNS, LDAP and IP address settings are finalised, prior to the installation of the SunRay Server Software.

Restart the Sun Ray DTU after powering the monitor on 3. Actions to take if this icon stays on for more than 10 seconds: 1. Cannot find module Program or installation error. Replace the DTU.

Whenever I insert a card into the SunRay unit the server is really slow at detecting it. It will be good if you are aware of how to solve the problem by yourself. The supported USB devices list is available at http://www.sun.com/io_technologies/sunray/usb/ 3. This icon is displayed only after the DTU successfully boots and receives an IP address, but then loses its Ethernet signal.

You can look up the meaning of the numeric OSD message codes in TABLE B-1 and the alphabetic DHCP state codes in TABLE B-2. Blinking PROM is corrupted. FIGURE B-6 Wait for Session OSD This OSD represents the transition state for the Sun Ray DTU. It stays up for few days and then hangs to 26B or 26D...

This icon is displayed as part of the normal startup phase and is usually displayed for only a few seconds. http://mmonoplayer.com/sunray-error/sunray-error-code-27d.html Monitor Display Resolution Defaults to 640 x 480 First, eliminate the most obvious possible causes: An older monitor A bad cable Monitor was off when the Sun Ray DTU was started Note - These error messages appear in English even in localized versions of Sun Ray Server Software. AuthModule.load Problem encountered while loading configuration module.

As latency and packet loss increase, performance suffers. Occasionally, the Sun Ray Client is first routed to another Sun Ray server. FIGURE B-8 No Ethernet Signal This icon indicates that the DTU has an Ethernet address and an IP address but has lost the Ethernet signal. this contact form Problem: The icon is displayed for more than 10 seconds.

Verify that the DHCP server is running and has not run out of IP addresses to assign to clients. Make sure that you are using a supported USB-serial adapter. AuthModule.load Problem encountered while loading configuration module.

I VPN Phase 2 complete.

Wait until the download is complete. Blinking PROM is corrupted. Updating Sun Ray Data Store schema ... Inserting a card at this point (and waiting for about 60s) will bring up the login greeter. * setting one of the sunrays as a token reader also requires leaving the

Definition: The DTU has passed the power-on self test but has not detected an Ethernet signal yet. CLIENT_ERROR--Indicates unexpected behavior from a DTU. Please check the log file, /var/log/SUNWut/utconfig.2005_11_10_13:24:57.log, for errors.If the SunRay server is not being used to serve web pages, save the following httpd.conf into the /etc/apache directory: httpd.conf Restart the apache navigate here This is due to the fact that obtaining a new operating system or device entails you to exhaust your resources.

Use utcapture to assess network latency and packet loss.