Home > Symantec Error > Symantec Error Pipe Close Failed

Symantec Error Pipe Close Failed

The maximum number is specified in the Media and Device Management volume configuration. And the UI displays “Preprocessing” during this stage of the virtual backup.  During this phase, a small amount of data is generated and is stored inside the guest virtual machine. Log that you need to look at if errors persist is bprd. I will check the logs and I take you a feedback after. 0 Kudos Reply What is "srv-smi-nbu-med"? navigate here

On a Windows NT client, set Verbose on the Troubleshooting tab in the NetBackup Configuration dialog box. This mode of transfer is usually slower than Fibre Channel. Status Code 84 ==================== media write error The system's device driver returned an I/O error while NetBackup wrote to removable media or a disk file. For a regular backup, the volume is automatically set to the SUSPENDED state and not used for further backups.

Create bpbrm and bpsched activity log directories on the server. 2. Run the following commands on the media server that services this backup to increase the unified logging levels: For Windows media server:\NetBackup\bin\vxlogcfg -a -p 51216 -o 134 -s DebugLevel=6 \NetBackup\bin\vxlogcfg -a -p Potential reasons include the following: * Reports were not emailed (possibly because of malformed email addresses in the vault.xml file). * On Windows, the third party mail client (such as blat) For example, if a slave server does not have a server list entry for the master, it does not accept connections from the master.

Open the cluster policy and close it again (the policy verification seems to sometimes contact the client and “let NBU client know that there is Change Journal enabled for this file Go to Solution. Status Code 205 ==================== cannot connect to server backup restore manager A process on the master server cannot connect to a process on a host on the network. Note: If you are using bpstart_notify scripts on UNIX or Windows NT clients, verify that messages are not being written to stdout or stderr.

On Windows NT clients, verify that the account used to start the NetBackup services has read access to the files. Status Code: 68 Top Message: client timed out waiting for the file list Explanation: The client did not receive the list of files to back up within the allotted time. This can be caused by a network problem or a problem with the process reading from the socket. Writing to a full disk partition. All rights reserved.

If the error logs show that it is associated with a subsequent error, it usually indicates a communication problem. Please also explain what you mean by 'restore byVault backup'? c. Status Code 130 ==================== system error occurred An error occurred that prevents the product from operating in a consistent fashion.

Recommended Action: Add the server name to the /.rhosts file on the UNIX client. Status Code 156 ==================== snapshot error encountered This status code indicates a snapshot-backup related error regarding Windows Open File Backup or Snapshot Client. Check the permissions on the parent directory and verify that NetBackup services are started with a "Logon as" account that has permission to create the directory. 3. o Set the NetBackup global attribute, Maximum Jobs Per Client, to 1 (note that this limits all clients in all classes). 4.

in Betrieb zu nehmen. http://mmonoplayer.com/symantec-error/symantec-error-r6025.html The getservbyname() function uses the name of the service to find a service entry in the services file (or NIS services map on UNIX if it is configured). Then a backup that requires the same drive is initiated before the mount completes. Status Code 154 ==================== storage unit characteristics mismatched to request A backup was attempted and the storage unit selected for use had the characteristics that were not compatible with the backup

through its phases to build its GRT view. For this case, try adding or modifying the CLIENT_READ_TIMEOUT and CLIENT_CONNECT_TIMEOUT values in the server's /usr/openv/netbackup/bp.conf file. Then, retry the operation and check the resulting activity logs. 2. his comment is here Is there a report I can run or somewhere in the GUI that will tell me the sum of all our data we backup?   Thanks Allan 8043391 1354641177

0 0 12/04/12--08:22:

System requirements vary; thus, no absolute recommendations can be made. This error can be encountered during a backup or restore. Once the VHD / VMDK files are mounted, following things are done: Registry information on the mounted guest are queried for the drive identification, (e.g assigned drive letter, boot records and

Status Code 223 ==================== an invalid entry was encountered A request to the bpdbm process (on UNIX) or the NetBackup Database Manager service (on Windows) had invalid information or some information

Enable ndmpd debug logging on the NAS device: For Network Appliance NAS, type the following to enable ndmpd debug logging:  ndmpd debug 70 EMC Celerra:  Enable debug logging on the datamover as Even with shared storage, and using SCSI pass-through (which on later versions of ESX is no longer supported), the media server wouldn’t be able to migrate between hosts. Recommended Action: 1. To display this dialog box, start the Backup, Archive, and Restore interface and click Configure on the Actions menu (also see "Using the Configure - NetBackup Window" on page 57).

Interview Questions 1.What is the diff between Netbackup .6x and previous verison 2.what are the files backedup under catalog backups 3.how can i recover an co... There has been a big push for disk being the primary backup target to completely replace tape, but tape is still a developing technology with LTO7 and LTo8 on the radar. o The General and Clients tabs in the NetBackup Configuration dialog box on Microsoft Windows and NetWare nontarget clients. weblink Check the progress report on the client for a message such as "Script exited with status code = number" (the number will vary).

Examine the resulting activity log file for detailed troubleshooting information. 4. Exclude deleted blocks Reduces the size of the backup image by excluding any unused or deleted blocks within the file system on the virtual machine. Status Code: 3 Top Message: valid archive image produced, but no files deleted due to non-fatal problems Explanation: The backup portion of the archive command reported problems so the files were Recommended Action: 1.

Corrupt binaries are one possible cause for this error. On Macintosh clients, this code can be due to multiple backups being attempted simultaneously on the same client. o If you cannot view the report, or you get a cannot connect on socket error when trying to view it, verify again that the NetBackup Database Manager daemon (or service) Status Code 43 ==================== unexpected message received The client and the server handshake was not correct.

Status Code 185 ==================== tar did not find all the files to be restored The tar file list contained files that were not in the image. o On Windows NT, 98, and 95 systems, the master server is designated as Current on the Servers tab in the NetBackup Configuration dialog box. VMware Credentials in Netbackup: Click Media and Device Management > Credentials > Virtual Machine Servers. Status Code 124 ==================== NB database backup failed, a path was not found or is inaccessible One or more of the specified paths in the catalog backup configuration were not backed

If necessary, update the server list. This error indicates that the client and server were able to initiate communications, but encountered difficulties in completing them. Status Code 69 ==================== invalid filelist specification The file list from the server had invalid entries. By this I mean don’t let someone trying to make a sale, sell you something you don’t need which inflates the costs; costs which can be spent elsewhere to maybe optimise

A possible cause for files not being deleted is that you do not have the necessary permissions. For example: this status appears if you add a new policy when an existing policy has the same name or definition such as attributes or clients. Recommended Action: Check the NetBackup Problems report for clues on why the error occurred. This option reduces the size of the backup image.

Status Code: 8 Top Message: unable to determine the status of rbak Explanation: On DomainOS clients, rbak is used to do restores. If this error is encountered, you may need to increase either the initial OTM cache size or the maximum OTM cache size, depending on the requirements of your installation and your This error can occur for incremental backups where no data was backed up because no files have changed. With a UNIX client, the email was not sent to an email address specified with USEMAIL in the client's bp.conf file.