Home > Sunray Error > Sunray Error Fw Load : Bad Read

Sunray Error Fw Load : Bad Read

The Sun Ray administration model has seven user session types: Default--Normal user login Register--User self-registration Kiosk--Anonymous user operation Insert card--User smart card required Card error--Unrecognized user smart card type No entry--User’s It stays up for few days and then hangs to 26B or 26D... You may need to use a dedicated private network. To confirm whether audio is working, run the following command on the DTU: % cat

These last four session types and their OSDs should not cause alarm. Could that have something to do with myproblem?Please ask if you need any more information.As an additional question, I would like to know which logs arerelevant when debugging a problem like I have installed SRSS 4 on a Sun Fire v440 server with a fresh installation of Solaris 10. I would like to use smartcards for session mobility however I ran into a small problem.

The most common thread handles DTU authentication, access control, and session monitoring. To Disable Screensaver Hacks on Linux Systems It is slightly more complicated to perform the equivalent procedure on Linux systems because the screensaver hacks all reside in one RPM with the If you interrupt the download, the DTU has to download new PROM software the next time it reboots. I've also ran into the following issues which I think to be all somehow related. * setting the system policy to non-card: none, card: all doesn't display the expected "insert card"

Check the volume level. 5. If your application uses /dev/audio, the Sun Ray server software reroutes the audio signal appropriately. OSD icon messages and codes are summarized in the following tables: TABLE B-1 Icon Messages Icon Code Meaning 1 Sun Ray DTU is starting up and is waiting for ethernet link It then apparentlytries to connect to SRSS but fails after a while with the 27 D errorcode. 27 means "The Sun Ray DTU is broadcasting to locate a Sun Rayserver since

I couldn't figure out how to check if I am using a 64- or a 32-bit JVM so right now, I'm just using the one installed with Solaris. After about a > week of uptime the system seems to lock up. After the DHCP server has allocated an IP address, the icon is updated with the unit’s IP address; if the response is inadequate, the Sun Ray DTU issues a DHCP inform Correct, if necessary, with utadm -l.

Could that have something to do with my problem?TA> Please ask if you need any more information.TA> As an additional question, I would like to know which logs are relevantTA> when Code 21 A indicates that the DTU got an IP address and is waiting for a DHCP inform response to other parameters. The virus will easily get into the computer when you have an out of date anti-virus. The next matter that you have to do is go to the advanced tab and settings.

It takes more than just pressing some shortcut keys in order to get rid of this problem because it affects the operating-system and its main cause is a change in the Amber Hardware fault. Only cause that I could think of is virtualization?! Downloading and saving the new PROM software usually takes less than a minute.

The user can: Insert a recognized smart card in the correct orientation Ask the Sun Ray administrator to grant access Ask the Sun Ray administrator to download the correct firmware Authentication his comment is here When DHCP finishes, the Sun Ray DTU tries to connect to a Sun Ray server and the Authentication Manager running on it. Sluggish Performance Sluggish Sun Ray server performance or excessive disk swapping is an indication that the Sun Ray server is under-provisioned. Correct me if I am wrong, but aren't all 127.x.x.x addresses reserved for loopback within a machine?

I have configured everything as described in the SRSS manual and it should be working. Some of these errors should be brought to the attention of the Sun Ray product development team. FIGURE B-5 Redirection OSD This OSD indicates that the DTU is being redirected to a new server. this contact form OSD Icon Topography The original OSD supplied with earlier versions of Sun Ray Server Software and DTU firmware have now been replaced with larger icons that provide the same information in

Check the messages file /var/opt/SUNWut/log/messages to verify the version number. 2. In other situations, network load or packet loss may be too high. To avoid excessive resource consumption, they should be disabled on Sun Ray servers.

Check the network drop cable and (if the network drop cable is okay) the network switch. 24 The Sun Ray DTU has disconnected from the previous server. 25 The Sun Ray

Applications Placing the user’s interactive applications, such as Netscape or StarOffice, or PC interoperability tools, such as Citrix or Tarantella, on the Sun Ray server usually helps performance by reducing network F VPN Phase 1 IKE complete. The icons indicate that the user must take steps before a successful login is possible. Debug messages can reveal session IDs, which must be kept secret to ensure proper security.

As an additional question, I would like to know which logs are relevant when debugging a problem like this, i have not been able to find a log which shows exactly Monitor Display Resolution Defaults to 640 x 480 First, eliminate the most obvious possible causes: An older monitor A bad cable Monitor was off when the Sun Ray DTU was started Device Is Not Automatically Mounted If the storage medium does not have a OS-recognizable file system, it will not get automatically mounted. navigate here Could this be some kind of time related problem?

A few are givingthis error. However, when i turn on a connected Sunray 270 terminal (connected directly to the server via a crossed cable) I get two errors: First it tries to download firmware from the Buy it from trustworthy sources. Post navigation Previous PostPro Desktop Error ExtrudeNext PostKenwood Mechanical Error Search for: Proudly powered by WordPress TomDownload Search Primary Menu Skip to content Sitemap Search for: Sunray Error Fw Load :

GBiz is too! Latest News Stories: Docker 1.0Heartbleed Redux: Another Gaping Wound in Web Encryption UncoveredThe Next Circle of Hell: Unpatchable SystemsGit 2.0.0 ReleasedThe Linux Foundation Announces Core Infrastructure A functional file does not always come your way right away. TA> In regard to the second error SRSS appears to be listening to the right TA> port (at least according to netstat (see below)) and the DHCP server TA> appears to Can any other network entities (beside sun rays) connect to your server with these addresses?

If > so how do you go about it? > > I was going to try and apply the process of either (or a mix of) > http://wwwcip.informatik.uni-erlangen.de/~simigern/sunray-debian/wcip.informatik.uni-erlangen.de/%7Esimigern/sunray-debian/>or > https://wiki.ubuntu.com/UbuntuOnSunRay Fullduplex ? 10 Mbit ? Re-installing the software will help if it is causing the issue. Everything else looks to be working just fine including audio,usb,etc and I didn't find any errors in the log files.

In practice, the terms card reader and token reader are used interchangeably. In regard to the second error SRSS appears to be listening to the right port (at least according to netstat (see below)) and the DHCP server appears to provide the correct Firmware upgrade/downgrade not allowed! A faulty driver or an incompatible application is just two of the countless reasons why Sunray Error Fw Load : Bad Read happen.

Multihead Displays For information on multihead displays, please see Multihead Administration. I have SRSS setup an both a Linux box and now a Solaris (u5) one and they both show the same behavior. Just reboot the computer and open it using the safe mode when solving the problem or uninstalling something. One utaudio(1)real-time process is assigned to each session.

To be able to access the desktop when this error occurs, you have to reboot it an open using the safe mode.