Home > Sunray Error > Sunray Error Codes

Sunray Error Codes

Then power cycle the DTU. Regards, --Robert S. Check the client's firmware version. For non-routed private interconnect configurations, the Sun Ray server also performs the functions of a DHCP server. http://mmonoplayer.com/sunray-error/sunray-error-codes-28e.html

Wait until the download is complete. Please do not change these modifications. We make no representation as to the accuracy or completeness of this data and are not responsible for errors or omissions. So for example - My filesystems are not full. - dtlogin does fork. - (as 26 D indicates) utauthd is running - no errors in /var/opt/SUNWut/log messages (but plenty of user

All Rights Reserved. 13.3. Troubleshooting Icon Quick ReferencePrev Chapter 13. Sun Ray Client Troubleshooting Icons Next13.3. Troubleshooting Icon Quick ReferenceNote Press the Mute-Softer-Louder keys or Ctrl-Pause-N keys simultaneously to display the current network status. F stands for full duplex, H stands for half-duplex mode.To display this OSD with current information, press the three audio volume keys simultaneously. The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open.

In very rare cases, network cables or switch equipment may be defective. 1. If not, the session can be enabled with soft security mode. The ASA will allow you to authenticate the incoming VPN user to LDAP (incl. If your application uses /dev/audio, the Sun Ray server software reroutes the audio signal appropriately.

No action is necessary. Multihead Displays For information on multihead displays, please see Multihead Administration. These error codes are listed in TABLE B-4. For LAN configurations with other (non-Sun Ray) DHCP services but no bootp proxy agent, verify the DHCP server and the Sun Ray vendor tags. 2.

The most common thread handles DTU authentication, access control, and session monitoring. All Rights Reserved. 13.12. (21) Network Connection Verified IconPrev Chapter 13. Sun Ray Client Troubleshooting Icons Next13.12. (21) Network Connection Verified Icon The Network Connection Verified icon indicates that the Sun Ray Client has detected the Ethernet NOTICE: SunMC agent failed to start. Card Read Error OSD Card Read Error Definition: The Card Read Error OSD icon appears whenever the firmware is unable to read the card due to one of the following causes:

Note - Sun Ray DTUs can function in a private interconnect or in a simple LAN environment with only an IP address, but additional basic parameters and Sun Ray-specific vendor options This icon is displayed as part of the normal startup phase and is usually displayed for only a few seconds. My system worked fine until I did the upgrade to last falls Solaris10 Upgrade. Restart the application.

FIGURE B-1 Ethernet Address OSD with Different Encryption and Authentication States Session Connection Failures The following icons are displayed when there might be a security breach. his comment is here The Sun Ray administration model has seven user session types: Default--Normal user login Register--User self-registration Kiosk--Anonymous user operation Insert card--User smart card required Card error--Unrecognized user smart card type No entry--User's GBiz is too! Latest News Stories: Docker 1.0Heartbleed Redux: Another Gaping Wound in Web Encryption UncoveredThe Next Circle of Hell: Unpatchable SystemsGit 2.0.0 ReleasedThe Linux Foundation Announces Core Infrastructure NOTICE "discarding response: " + param No controlling application is present to receive DTU response. "NOT_CLAIMED PARAMETERS: " + param A token was not claimed by any authentication module.

OHH = Overheat. To confirm whether audio is working, run the following command on the DTU: % cat /usr/demo/SOUND/sounds/whistle.au >/$AUDIODEV 2. FLO, FL, FLC, FL1, PS, Blinking Lights Pressure Switch or Flow Switch Failure. http://mmonoplayer.com/sunray-error/sunray-error-codes-27b.html Downloading and saving the new PROM software usually takes less than a minute.

Code 21 A indicates that the DTU got an IP address and is waiting for a DHCP informresponse to other parameters. ICE = Freeze protection. Make sure that you are using a supported USB-serial adapter.

Copyright © 2011, 2012, Oracle and/or its affiliates.

If one of these sensors needs to be replaced BOTH should be replaced at the same time. Do not use spa when temperature is flashing or the OH message is displayed. TABLE B-4 Firmware Download Error Codes and Messages Error Code Error Message E FW Load: No server F FW Load: Name too long G FW Load: Bad read H FW Load: Thorvaldsen" Sent: 23.

drops. This icon is displayed as part of the normal startup phase and is usually displayed for only a few seconds. To Identify a Hung Session As superuser, type: # /opt/SUNWut/sbin/utdesktop -l -w To Kill a Hung Session As superuser, type: # /opt/SUNWut/sbin/utsession -k -t token Actions to Take 1. navigate here You could save great amount of cash when you know how to troubleshoot Sunray Error Codes in case your computer is experiencing one.

This technique produces slow Sun Ray performance. type crle at the command prompt and see if it returns a large amount of data. I am very glad about any ideas here. Run the following command to find stale mount points. # /opt/SUNWut/bin/utdiskadm -s Note - Close all references to the mount point or terminate all processes that refer to the mount before

Use utcapture to assess network latency and packet loss. A basic ASA5505 should be around US$500, good for 25 remote users I think. Recent Msgs:commits.gnome/2016-12/msg00023.htmlubuntu-bugs/2016-11/msg15855.htmlgeneral/2016-12/msg00005.htmlwp-trac/2016-11/msg03147.htmlgeneral/2016-12/msg00152.htmlcommits.gnome/2016-12/msg00038.htmlxen-development/2016-12/msg00001.htmlubuntu-bugs/2016-12/msg00024.htmlcentos/2016-12/msg00001.htmlgeneral/2016-12/msg00107.html Latest News Stories: Linux 4.0 Kernel Released Google Lets SMTP Certificate Expire Open Crypto Audit Passes TrueCrypt CIA 'tried to crack security of Apple devices' Xen Security Bug: Amazon, For non-routed private interconnect configurations, the Sun Ray server also performs the functions of a DHCP server.

Cannot find module Program or installation error. Cannot find module Program or installation error. This technique produces slow Sun Ray performance. Verify that the DHCP server is running and has not run out of IP addresses to assign to clients.

Verify that Mute is not selected. Sun Ray System Software provides a redirection library that you can use to correct this behavior. A large red X drawn through a lock symbol next to a green check mark with no IP address indicates that the client refuses to connect. This error can occur only if an unknown Sun Ray server intercepts the messages and tries to emulate a valid Sun Ray server.

Debug messages can reveal session IDs, which must be kept secret to ensure proper security. Verify that audio output is selected properly, for example, for headphones or speakers. 4. toukokuuta 2008 11:44 To: [email protected] Subject: [SunRay-Users] Re: SRSS lockup on Linux -------- Original Message -------- Subject: Re: SRSS lockup on Linux Date: Thu, 22 May 2008 17:24:41 +0200 (CEST) From: As latency and packet loss increase, performance suffers.

CallBack#--Communicate with applications such as utload.