Home > Sunray Error > Sunray Error Code 28f

Sunray Error Code 28f

Access Denied OSD Access Denied Definition: The Access Denied OSD icon appears when the current authentication policy denies access to the presented token. This icon is displayed only after the DTU successfully boots and receives an IP address, but then loses its Ethernet signal. To display large images, use shared memory pixmaps, if possible. After the DHCP server has allocated an IP address, the icon is updated with the unit’s IP address; if the response is inadequate, the Sun Ray DTU issues a DHCP inform http://mmonoplayer.com/sunray-error/sunray-error-code-28e.html

Tip - To get the same effect on non-Sun keyboard, disconnect and reconnect the Ethernet cable. Such DTUs must be upgraded with Sun Ray Server Software 2.0 firmware before being deployed on a shared subnet, if the deployment strategy requires a two-step DHCP interaction. Encryption and authentication information is also displayed when appropriate. Tip - If you suspect that the configuration files have been corrupted, please see Determine the Integrity of the Configuration Files in the Sun Ray Server Software 4.0 Installation and Configuration

GXcopy mode is usually the fastest drawing mode. One solution would be a small, dedicated interconnect on one Sun Ray server. Thanks Deniz.Yes. Confirm that the DHCPServer and INFORMServer values are appropriate.

Actions to take: 1. For routed configurations, verify that the bootp proxy agent is configured correctly in the Sun Ray DTU's subnet and that it points to one of the Sun Ray servers in the Warning: Apache is not installed on this system. Be ready to provide the following:JRE installation path.Apache Tomcat installation path.From now on, the SRSS installation path (/opt/SUNWut) will be referred to as SRSS_INST.Upon script termination it's now required that you

This condition occurs when the Sun Ray Client receives an IP address from the DHCP but no other parameters. Google Authenticator: Using It With Your Own Java Authentication Server The Google Authenticator application for mobile devices is a very handy application that implements the TOTP algorithm (specified in RFC 62... Packages * bug submitted - see below The following packages are to be installed: ldap-utils SRSS utilises an LDAP server to store configuration info dhcp3-server SunRays require a DHCP server to These messages can be generated during normal operation if a DTU is rebooted.

OSD 4 now includes error code text, as shown above. Sluggish Performance Sluggish Sun Ray server performance or excessive disk swapping is an indication that the Sun Ray server is under-provisioned. The problem can usually be traced back to an older version of the dtlogin daemon or the configuration files for the dtlogin daemon. However, performance of the Sun Ray Client might be affected.

Please try the request again. In earlier releases, the wait icon was displayed as a green newt cursor. adding new entry "o=utdata" adding new entry "o=v1,o=utdata" adding new entry "utname=naaman,o=v1,o=utdata" adding new entry "utname=desktops,utname=naaman,o=v1,o=utdata" adding new entry "utname=users,utname=naaman,o=v1,o=utdata" adding new entry "utname=logicalTokens,utname=naaman,o=v1,o=utdata" adding new entry "utname=rawTokens,utname=naaman,o=v1,o=utdata" adding new entry If your application uses /dev/audio, the Sun Ray server software reroutes the audio signal appropriately.

CallBack#--Communicate with applications such as utload. http://mmonoplayer.com/sunray-error/sunray-error-code-27d.html invalid key: DTU does not properly implement the authentication protocol. The client is a secondary client in a multihead group, and the primary client is not currently connected. 62 Server Policy Token reader. FIGURE B-10 Ethernet Address OSD with Different Encryption and Authentication States Session Connection Failures The following icons are displayed in the event of a possible security breach.

Configuring Sendmail on Solaris 10 Part 2. The smart card token itself is an integrated circuit embedded in or printed on the card, and it is data on the token that is read when a user inserts a For LAN configurations with other (non-Sun Ray) DHCP services but no bootp proxy agent, verify the DHCP server and the Sun Ray vendor tags. 2. navigate here After successfully setting up Ubuntu to run SRSS 3.1, I wish to provide an easier-to-follow, Ubuntu-tailored version of the SunRay Debian guide.

To avoid excessive resource consumption, they should be disabled on Sun Ray servers. Audio Device Emulation The emulated audio device follows the user session during hotdesking. These last four session types and their OSDs should not cause alarm.

July 9, 2010 at 4:28 PM Grey said...

Inspect the log file /var/opt/SUNWut/log/utstoraged.log for an indication as to why device nodes were not created. If the firmware download fails, the following syslog message indicates that the barrier level has been set to prevent Sun Ray DTUs with SRSS 4.0 firmware from automatically downloading an earlier If not, look at your bootp relay configurations and DHCP server configurations for network and Sun Ray parameters. Error encountered while reading messages from the DTU. .../...

Click OK. Starting the SunMC agent... Cannot find module Program or installation error. his comment is here This is a great post, I understand that one might want to do this for a POC but have you had any chance to actually test this with more than one

If the DTU is connected through a hub or a switch, make sure that the hub or switch is powered on and configured correctly. If not, the session can be enabled with soft security mode. FIGURE B-14 VPN Connection Established Firmware Download Diagnostics When firmware download error occurs, OSD icon 4 (see FIGURE B-15) displays the appropriate error code and a descriptive text string. Note - For LAN configurations, the minimum barrier level is 200.

Verify that it is configured properly for DHCP services. Issues Being Investigated BugID 326796 - gdmdynamic fails to remove a dynamically created display correctly when using the command /usr/bin/gdmdynamic -b -d $DISPLAY and causes gdm to not display the gdmgreeter Amber Hardware fault. In very rare cases, network cables or switch equipment may be defective. 1.