Home > Sundance Spa > Sundance Spa Troubleshooting Fl1

Sundance Spa Troubleshooting Fl1

Contents

This means I might get my order by 2015. One sensor has detected 118º F at heater. The pumps usually run during this time until the spa is out of freeze danger. If there is no blockage at the psi switch you may have a bad psi switch. this contact form

I currently have an order pending from a site that I ordered a new filter, some fix-a-leak, and a couple other items. Manassas Park, VA Reply With Quote « Previous Thread | Next Thread » Forum > Swimming Pool Care > Spas and Hot Tubs > Trouble with Sundance spa- FLO error and You could also drain the spa, disconnect the unions and stick your finger inside the pump housing to try and turn the impellor. Düşüncelerinizi paylaşmak için oturum açın.

Sundance Spa Troubleshooting Fl1

And kicks out and starts all over again please help. I also believe that my circulation pump is causing these issues. Try turning off your spa and unplugging your sensor harness J2 on your PWA and then re-applying power to the spa.

If the error code goes away and you are getting the proper voltage then replace the pressure switch/flow switch. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. Still same problem. Sundance Spa Temperature Sensor If all else fails contact our Service Support Desk to book a diagnostic and repair of your Sundance Spa.

Power failure. Sundance Spa Flo Error FWIW, I found that the tub is indeed a Capri, made in 1998. Thank you, Gary Dan B January 31, 2014 Reply We have a Sundance Spa Constance (2011) and today also noticed the FL1 error code. FINAL NOTE: Most spas are equipped with pressure switches and can be found threaded into the stainless steel heater manifold.

Water level is good. Sundance Spa Circulation Pump The water is still very clear and chemicals are easy to keep balanced (thanks to the great advice I got from this forum). Spaminator provided by [OzzModz] Spaminator - vBulletin Mods & Addons Copyright © 2016 OzzModz Ltd. If there is any more info that you guys need from me I will be happy to try and provide it.

Sundance Spa Flo Error

Low speed pump and heater will activate until spa reaches 65ºF. What would be the issue if it will not turn off. Sundance Spa Troubleshooting Fl1 The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open. Sundance Spa Flow Switch Chad Senior Member Posts: 1990 2006 Jacuzzi J-345 Re: Sundance FLO error.... « Reply #3 on: November 13, 2007, 06:26:33 PM » He's only had the filter for a month.

I have a new filter on order right now, but I'm afraid I may have to replace the circulation pump also. weblink I contacted Aquatech and they suggested I clean the filter with the FilterBrite. Chiprva June 21, 2016 Reply Hello Nigel, I have a sweetwater Palermo LX15, DOM 3/11/00, SN PL381278-0300, 240V. Spa has shut down. Sundance Spa Flo2 Error

No water is circulating and the "heating tube" is cold however, the electric motor attached to the pump with the two main feed lines is very hot. HotTubBarn 24.393 görüntüleme 9:51 FLO Error Code - Süre: 0:43. January 31, 2014 Reply Dan typically when you have an FL1 code it means the spa is not heating and won't heat until the FL1 code is addressed so you want http://mmonoplayer.com/sundance-spa/sundance-spa-uv-bulb.html My spa cables are colour coded to European regulations where brown is live and blue is neutral.

Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. Sundance Spa Flow Switch Testing When the company opened Iit for the summer they blew the circuit board. All Rights Reserved.

Our tub has FL1 error, and I realized after reading your message that our waterfall also stopped.

I removed the panel just to the right if the circuit board so I could see what was going on. I have also run the tub for a few minutes on pump 1 to see if that shakes the flow switch loose, it didn't clear the error. Check to see if you can hear any noise at all from the circ pump with a heat call. Sundance Spa Heater Not Working http://www.spaandpoolsource.com/pdf/sun ...

If the wire is bad go ahead and replace the wire. Dave June 19, 2016 Reply I have Sundance chelsea with fl1 error code. Do not enter the spa. his comment is here We hope to see you soon!

If alternating with temp, may be temporary condition.