Home > Sundance Spa > Jacuzzi Watchdog Reset

Jacuzzi Watchdog Reset

Contents

If you power the spa back on and the problem goes away then you are good to go. What do I do? Q: My control displays the error code "CF". Details Have one to sell? Check This Out

Verifying that the old sensor was bad by hooking up the new one electrically before mechanically installing it in the spa. Is the spa has more than one spaside control, disconnect all but the main control panel and restart the spa. By Bruce Byler on October 5, 2016 Verified Purchase My temp in my Jacuzzi J370 was reading 94 but felt like 104.. Was this review helpful to you?

Jacuzzi Watchdog Reset

Check for Flow/Pressure Switch problem.FL2:Flow switch or pressure switch closed when pump is not running. We purchased this replacement temp sensor and what a difference it made! The hot tub will stay in this mode until the water temperature reaching 15 degrees below the set temperature. If you have at least a little handyman ability you will be fine.

Make sure the circ pump works, it is often best to wire the circ pump into the main incoming power and ensure the heater circulation pump functions. Sorry, we failed to record your vote. Mr. Sundance Spa Flo Error Q: My control panel reads the error code "FL2." What do I do?

Try to reset power to spa. If debris is present, remove debris, install switch and test system. Please try again Report abuse 5.0 out of 5 starsReplaced High-limit sensor to fix "0000" watchdog error on J-370 By Bill M. Contact your Sundance Spas dealer or qualified service technician. "WATCHDOG" (hot tub is deactivated).

Was this review helpful to you? Sundance Spa Temperature Sensor Power failure. Was this review helpful to you? This must be repaired only be a Sundance Spas dealer or qualified service technician.

Sundance Spa Reset

We tend to symptomatically work through these looking for the cause. Sorry, we failed to record your vote. Jacuzzi Watchdog Reset If you suspect that this is the case, see the instructions on page 77 under "pump does not operate and icon does." Circuit board temperature has exceeded acceptable limit. Sundance Spa Reset Change Filter By Adam Kelley on December 16, 2015 Verified Purchase Saved me a $100 service call, plus my local dealer marked the price of this part up by 75%.

Alright.  What causes the Watchdog error?  MOST of the time, this is caused by a faulty temp sensor or flow switch, possibly a circuit board.  On very rare occasions it could Watchdog is a general error code and does not have one specific cause, below is a listing of the things we recommend checking when trouble shooting a watchdog failure. Contiguous US only - Free Shipping is not available to Alaska or Hawaii. Good eyesight is useful as two of the connections are very small. Sundance Spa Troubleshooting Fl1

Your Recently Viewed Items and Featured Recommendations › View or edit your browsing history After viewing product detail pages, look here to find an easy way to navigate back to pages It is the small metal sensor attached to the side of the heater tube. A: This is very much like our "CF" where nothing is actually wrong. this contact form Learn more about Amazon Prime.

We always recommend having work done by a factory trained professional. Sundance Spa Flo2 Error Related Video ShortsPage 1 of 1Start OverPage 1 of 1Previous page 10:59 Customer Review:Best Online Price for a Common Sundance Spas Replacement Part Next page Sponsored Products Related To This Item Remove hot tub cover to speed cooling.

I guess I was just lucky all these years.The manual (p.14) states that neglecting to fill through filter bucket may cause air to be trapped in either pump, preventing the pump

Replace the main circuit board and the transformer. Was this review helpful to you? The " - - - - " was gone and the ambient air temperature (the new sensor was laying on the ground) showed on the spa display as 61 degrees. Sundance Spa Heater Not Working A solid red light indicates that immediate attention is required to clear or fix an error code.

My temperature probe gun showed the sensor button to be 63 degrees (close enough).2. UV bulb needs to be replaced. A: This is usually the temperature sensor. navigate here Watchdog is a catastrophic failure of more than one component.

Site by Take 42 ...Tips And information For Spa Dealers And Service Techs « Back June, 2013 Sundance Watchdog Mode By - Your Spa Parts Plus Tech Team One of Check wiring harness, If wiring harness tests OK, then Circuit Board is possibly defective.5. Yes No Sending feedback... If the error code goes away then clean or replace your filters.

Sell on Amazon Image Unavailable Image not available forColor: Sundance Spa Temp Sensor #6600-167 by Sundance Spas Temp Sensor 4.5 out of 5 stars 33 customer reviews | 23 answered questions Carlsbad: (760) 431-7727 | San Diego (858) 675-7727 Find Your Perfect Hot Tub J-500 Collection J-585™ Seats: 5-7 Jets: 52 J-575™ Seats: 5-6 Jets: 53 J-400 Collection J-415™ Seats: 2-3 Jets: Measure resistance across switch terminals for continuity. Details Sold by Pacific Spas & Sauna and Fulfilled by Amazon.

Details Deal of the Day: Holiday savings on Vivere Double Hammocks Today only, shop Vivere Double Hammocks, and save. That means cut the power, remove filters, blow water through the lines with your garden hose, and power on. If not, cut the power again and remove the filters. Please try again Report abuse 5.0 out of 5 starsExactly What I Needed.

Feedback Sundance MicroClean Filter Ultra Outer Filter Only #6473-165 3.9 out of 5 stars 13 $68.70 Prime Feedback Spa Frog Mineral Sanitizer 4.3 out of 5 stars 98 $24.50 Prime Feedback Thank you for your feedback.